Bowers & Wilkins CDA-4D DSP Amplifier, 4 Channel 125 watts, Black (FP43648)

CDA-4D Front Panel with Feet
CDA-4D Front Angle with Rear Ears
CDA-4D Rear Panel with Feet
CDA-4D Front with Rear Ears

Additional Information

Description Specification Downloads

Bowers & Wilkins CDA-4D DSP Amplifier, 4 Channel 125 watts, Black

The CDA-4D is a compact distribution amplifier, designed to power current and future Bowers & Wilkins Custom Installation loudspeakers. Embedded DSP allows optimisation of a wide range of products and dynamic EQ for Bowers & Wilkins subwoofers. It boasts four channels of 125 watts each, and its full-rack-width 1U design delivers high-performance from minimum rack space.

Impressively smart

To ensure the CDA-4D delivers in the modern custom installation system, it is equipped with Digital Signal Processing (DSP). This allows it to be used in wide variety of situations, provides control over IP and configuration, and for providing dynamic EQ for Bowers & Wilkins subwoofers.

Compact powerhouse

CDA-4D’s 1U size means that it takes up the minimum of rack real estate. But with four channels of 125 watts of Class D amplification on hand it can deliver power when required. Plus, as it’s bridgeable this can be configured to 2 x 250 watts, or a 2.1 setup (2 x 125 watts and 1 x 250 watts), where needed.

Flexible

Whether you are looking to upgrade an in-situ installation or planning a new one, the CDA-4D DSP amplifier is ideal. It can drive two zones, and works with a wide variety of Bowers & Wilkins products, both current and future

Audio Specifications
Load impedance range: >3Ω per channel (>6Ω in bridge mode)
Output Power per channel, non-clipped: 60W into 8Ω
125 into 4Ω
Output Power bridge mode, non-clipped 500W short term
>125W continuous
DC offset voltage: <50mV
Frequency Response (-3dB): <10Hz to >30kHz, any load impedance
Frequency response accuracy, 20Hz-20kHz: +/-1dB
Dynamic range: >85dB A-Weighted
THD+N (1kHz, 500W, 4Ω): less than 1%
Voltage Gain: 15dB to 39dB, adjustable
Input impedance: 10kΩ
Maximum input voltage: 4 Vrms
Signal sense threshold: 2.5mV (independent of Gain setting)
Wake-up time: <0.2s (If other zones active)
<2s (From all zones inactive)
Turn-off time: 15 minutes from last signal detected
12V trigger input threshold: Typically 3V (recommended input is 5-15V) (TBC)
Controls and Indicators
Front panel: 1 x Power LED (unit active – White, Fault – Red)
1 x Network status LEDs (Signal present – White, Fault – Red)
2 x Zone status LEDs (Signal present – White, Fault – Red)
1 x Reset button
Connectors
Input: 2 x RCA (pair) Phono socket, Analogue line in
2 x RCA Phono socket, Digital line in
1 x Ethernet
Output: 2 x 5.08mm Pitch 4-way Phoenix Combicon style
12V trigger control: 1 x 3.5mm jack - 12V trigger IN
1 x 3.5mm jack - 12V trigger OUT (Maximum 100mA pass-through
Power
Power consumption: <0.5W Standby, WoL disabled
<2W Standby, WoL enabled
300W maximum average (TBC)
1,000W peak (TBC)
AC supply: 100-240V 50/60Hz
AC inlet: IEC C14, switched
Thermal
Thermal dissipation: TBC BTU/hr (standby)
TBC BTU/hr (Idle)
TBC BTU/hr (max)
Dimensions
Height: 42.5mm (1.7in) 1U (57.5mm (2.3in) plus feet
Width: 436mm (17.2in)
Depth: 300mm (11.8in)
Net weight: 4.0kg (8.8lb)
Warranty Info
Manufacturer's Warranty*: 2 Year Return To Base
Faulty From New*:
(Within 14 Days Of Purchase):		 Return to AWE for assessment.
Please complete this online Returns Form
After 14 Days Of Purchase*:
(Within The Manufacturer's Warranty)		 Return to AWE for assessment.
Please complete this online Form
Post-Warranty Service and Repair: Please contact an authorised service centre: Sontec or Sound System Technology
*Terms & Conditions: For further information regarding AWE's returns procedures please see chapters 7 & 8 in our Terms & Conditions

Features

  • Boasts four channels of 125 watts
  • Full-rack-width 1U design
  • Embedded DSP
  • Class D amplification

Related Products

ISW-6 Front Angle Grille On

Bowers & Wilkins ISW-6 2 x 3'' 7 In-wall Subwoofer (FP42897)